Department of Mechanical Engineering

Book Chapter
Singh K. P., Kumar A., and Kaushal, D.R.(2019), CFD modelling and experimental investigation of bi-modal slurry flow in horizontal pipeline and bends, Book series Lecture notes in Mechanical Engineering (Springer).(SCOPUS indexed Q4) ISSN NO:21954364, book title Advances in Fluid and Thermal Engineering. DOI 10.1007/978-981-13-6416-7. (5 citations)

Publications in International Journal
1.     Singh K. P., Kumar A., and Kaushal, D.R.(2019), Experimental investigation on effects of solid concentration, chemical additives, and shear rate on the rheological properties of bottom ash (BA) slurry, International Journal of Coal Preparation and Utilization, Taylor and Francis Publications, (http://dx.doi.org/ 10.1080/ 19392699.2019.1636787) (2025 SCI Impact Factor: 2) (SCOPUS indexed Q2) (13 citations)
2.     Singh K. P., (2020) “Study of Process Parameter and Microstructure of Freeze Casting Technology: A Review “IOP Conf. Series: Materials Science and Engineering 804(2020)012021. IOP Publishing doi:10.1088/1757-899X/804/1/012021(SCOPUS indexed Q3) (7 citations)
3.     Singh K. P., (2020)“A Study on Coal Ash Slurry Flow at Higher Solid Concentrations in Pipeline” Springer Nature Singapore Pte Ltd. 2020 S. Yadav et al. (eds.), Proceedings of International Conference in Mechanical and Energy Technology, Smart Innovation, Systems and Technologies 174, pp 817-822.https://doi.org/10.1007/978-981-15-2647-3_77. (SCOPUS indexed Q3) (6 citations)
4.     Singh, K.P, Kumar, A. and Kaushal, D.R. (2019), “Pressure drop calculation for fly ash slurry using rheological model”, World Journal of Engineering, Vol. 16 No. 6, pp. 751-767. ISSN:
1708-5284, https://doi.org/10.1108/WJE-03-2019-0086.World Journal of Engineering (SCI Impact Factor: 1.4, SCOPUS indexed Q2) Emerald publication. (7 citations)
5.     Singh K.P., Kumar A., and Kaushal, D.R.(2018),Computation modelling for fine particle flow in horizontal slurry pipelines, International Journal of Research and reviews: Journal of Physics ISSN: 2278-2265 (Online), ISSN: 2347-9973 (Print) volume 8(1)pp 1-6.(UGC approved). (4 citations)
6.     Singh K. P.,(2018) CFD modelling of silica sand slurry flow through straight pipelines and bends using FLUENT, International journal of computation engineering research, ISSN (e): 2250 – 3005,Volume 8(5) pp 47-51 (UGC Approved) (5 citations)
7.     Singh K. P., (2018) Performance analysis of centrifugal pump used in slurry pipeline transportation by CFD modelling in ANSYS 15, International Journal of Enhanced Research in Management & Computer Applications, Volume 7(2) pp. 437-442 (4 citations)
8.    Singh K. P., (2018) Nanotechnology and Nano-materials: an advance developing approach for Indian Industries. International Journal of All Research Education and Scientific Methods (IJARESM) ISSN: 2455-6211, Volume 6, Issue 4, April- 2018. (3 citations)
9.     Singh K. P., N Sura, (2018) Experimental Study on Effects of Process Parameters on HAZ of Plain Carbon Steel Using GMAW, in International Journal of Latest Research in Science and Technology,Volume 2(4) pp 167-170(ISSN 2394 – 3386) (8 citations)
10.  Arvind Kumar, Singh K. P., Bhupender Singh “CFD modeling for Silica sand slurry in horizontal pipeline system” YMCAUST International journal of research, july 2015 vol3(2) ISSN:2319-9377. (3 citations)
11.  Singh K. P., Sheoran R, Phogat S., (2017) “Effect of addition of Fe-Si on mechanical and metallurgical behavior of Al Powder Metallurgy (PM) product” International Journal of Material Sciences (ISSN No. 0973 – 4589) . 67-72 (2 citations)
12.  Singh K. P., Singh R., Phogat S (2017) “Experimental Analysis of Surface Roughness and Machinability parameters of Al base Alloys with material additives (Fe-Si)” International Journal of Material Sciences (ISSN No. 0973 – 4589) pp. 57-65 (2 citations)
13.  Phogat S., Sheoran R, Singh K. P., (2017) “Review on elements for Just in Time implementation in Indian service sector” International Journal of Theoretical and applied Mechanics (ISSN No. 0973 – 6085) pp. 103-111 Research India publication. (2 citations)
14.  Singh K. P., Phogat S., Sheoran R. (2017) “Experimental study of effect of process parameter of GMAW welding on mechanical properties and microstructure of steel (SAILMA 350 HI)” International Journal of Theoretical and applied Mechanics (ISSN No. 0973 – 6085) pp. 113-123 (6 citations)
15.  Phogat S., Sheoran R, Singh K. P., (2017) “Intelligent approach for balancing of workload on machines for loading of machines in manufacturing” International Journal of Theoretical and applied Mechanics (ISSN No. 0973 – 6085) pp. 125-134 (3 citations)
16.  Sheoran R, Singh K. P., Phogat S (2017) “Analytical evaluation of steering errors in a front wheel steered vehicle” International Journal of Mechanics and Solids (ISSN No. 0973 – 1881) pp. 53-59 Research India publication. (3 citations)
17.  Kumar A., Singh K. P., Gupta, S. and Kaushal, D.R. (2015), CFD Modeling for Solid-Liquid Flow in Pipeline, YMCAUST International journal of research, Jan 2015 vol3(1) ISSN:2319- 9377, pp105-109(5 citations)
18.  Singh K. P., A. Gupta, K.M. Assefa and D.R.Kaushal,(2015),”Experimental Investigation on the Rheological Behaviours of Fly Ash Slurries without and with the Addition of Chemical Agents”, RACEE-2015,Proceedings online in International Journal of Engineering Research & Technology(IJERT)(ISSN: 2278-0181) pp. 196 – 200.Impact factor 3.06. (9 citations)
19.  Kumar A., Singh K. P., Gupta, S. and Kaushal, D.R. (2014), “CFD modeling for pressure drop in pneumatic conveying through pipe bend”, International Journal of Advances in Engineering Sciences Vol. 4, Issue 3, July 2014 Print-ISSN: 2231-2013 e-ISSN: 2231-0347 (9 citations)
20.  Kumar A., Singh K. P., Gupta, S. and Kaushal, D.R. (2014), CFD Modelling of Slurry Flow in Pipeline System for Solid Concentration Distribution, International Journal of Applied Engineering Research (ISSN:0973-4562), Vol.9, No.7 Special Issue, pp 733-742. (SCOPUS Index) (5 citations)

  Papers presented/published in National Conferences:
1.     “Advancement in Nano-materials and Nanotechnology for use in Indian Industries – An Overview” national conference on role of science and technology towards ‘Make in India’ RSTTMI-2016, YMCAUST Faridabad, March 2016 (2 citations)
2.     “Experimental study of rheological behavior of Fly Ash at low and medium concentration with and without use of chemical additives” national conference on recent advancements in civil and environmental engineering (RACEE-2015) 28th-29th November 2015(4 citations)
3.     “CFD modeling of slurry transportation in pipeline for Concentration Distribution using different models” national conference on recent advances in mechanical and civil engineering (RAMCE-2014), Ghaziabad during 4th-5th april, 2014(5 citations)
4.     “Effect of process parameters on hear affected zone using gas metal arc welding” Proceeding of National Conference on Recent Trends and materials engineering held at BRCM CET, Bahal during 4th-5th October, 2013. (5 citations)
5.     “Optimization of parameters in welding of MS plates” Proceeding of National Conference on Recent Trends and materials engineering held at BRCM CET, Bahal during 4th-5th October,2013
6.     “CFD Modelling of particulate flow (2 phase flow) in pipelines using FLUENT Software” Proceeding of National Conference on Recent Trends and Material Engineering held at BRCM CET, Bahal. pp 386-396, 4th-5thOctober, 2013 (5 citations)
7.     “Numerical simulation of finer particles at higher concentration for pipeline flow” Proceeding of National Conference on Recent Trends and Innovation Civil Engineering held at BRCM CET, Bahal.pp140-145, 15th-16th November, 2013(3 citations)
8.     “CFD Modelling for Slurry Pipeline Flow: A Literature Review” Proceeding of National Conference on Recent Trends and Innovation Civil Engineering held at BRCM CET, Bahal. pp 146-150, 15th-16th November, 2013(3 citations)
9.   “An Analysis of Surface Roughness and Machinability of Al-Fe-Si Alloys”, Proceeding of National Conference TAME-2012, October 19-20, 2012, YMCAUST, Faridabad (Haryana).
10.  “An Analysis of Sintering Mechanism”, Proceedings of National Conference on Recent developments in Mechanical Engineering, 19-20 February, 2010, pp 272-275, BRCM-CET, Bahal, Haryana ISBN No 978-93-80043-81-4.
11.  “Powder Metallurgy (PM) of Aluminium Alloy”, Proceedings of National Conference on Recent developments in Mechanical Engineering, 19-20 February, 2010, pp 208-211, BRCM-CET, Bahal, Haryana ISBN No 978-93-80043-81-4.
12.  “Cogeneration of Energy”, Proceedings of National Conference on Industrial Electronics, Drives and Embedded Systems, March 7-8, 2009, BRCM CET Bahal, Haryana.
13.    “Sintering Technology: An Analytical Overview”, Proceedings of NCTI, October 11-12, 2008, pp 418-423, BRCM CET Bahal, Haryana.

Papers presented/published in International Conferences:
1.     Experimental investigation on effects of chemical additives on rheological behavior of fine particle bottom ash slurry, International Conference on Startup ventures: Technology Developments and Future Strategies (SV-TDFS) 2018held at Manipal University, Jaipur, Rajasthan, India on October 8-9, 2018
2.     “Rheological analysis and CFD modelling of FA slurry at different particle size in straight pipeline using ANSYS” International conference on sustainable development through research in engineering and management (SDREM-16) held on 26-27 December 2016 at YMCAUST, Faridabad. (8 citations)
3.     “Experimental investigation of effects of chemical additives on the rheological properties of slurry in sustainable pipeline transportation” International Conference cum Workshop on “Tools, Techniques and Practices for Improving Sustainable Manufacturing” GLA University Polytechnic 23rd -24th January 2016. (4 citations)
4.     “Simulated Study of Feasibility and Design of 10 KWp STV” Proceedings of 2nd International Conference on ESTEEM-2013, March 3-4, 2013, PPIMT Hisar (Haryana).
5.     “Simulation of Thermal Power Plants”, Proceedings of International Conference on Innovative Technologies, p-662, June 18-19, 2009, PDM Bahadurgarh (Haryana).
6.     “Modern World Class Manufacturing Scenario”, Proceedings of International Conference on Innovative Technologies, p-681, June 18-19, 2009, PDM Bahadurgarh (Haryana).
7.     “Development of Robot Technology” Proceedings of International Conference on Innovative Technologies, p-660, June 18-19, 2009, PDM Bahadurgarh (Haryana).